![]() If so, then diabetics unable or uninterested in the high expense associated with traditional CGMs may be attracted to it. ![]() The company expects to price it similarly to glucose strips and glucose meters. If sugarBEAT is commercialized, it could be an intriguing alternative to existing CGMs for non-insulin intensive patients. In the U.S., management thinks it can submit the device for FDA approval by the end of Q1 2019. Then, if all goes well, it will roll the product out in other European markets. Nemaura Medical plans to launch sugarBEAT in the United Kingdom before the end of 2018. Previously, the company reported results indicating "84.3% of the data points had an overall MARD of 10.63%, and an overall nominal MARD of 16.3%." For comparison, the MARD for Dexcom's G5 and its newest CGM, the G6, is about 9%. Nemaura said that the numbers were "in line with the company's expectations, and compare favorably with competitor products." MARD is a measure of a CGM's accuracy and the lower the number, the greater the accuracy. In 25 patients with either type 1 or type 2 diabetes, the mean absolute relative deviation (MARD) 30%/30mg/dL for 1-point calibration was 12.19%, and for the 2-point calibration, it was 10.65%. Honestly it’s a wonder that our computers even work.On Wednesday, management provided an interim update from one of what's expected to be a "number of planned studies" in support of a filing for Food and Drug Administration (FDA) approval. Of course this is all a lot more complex than it really needs to be. Naturally you are unlikely to have it installed on your Windows machine.) (There are ways to do that same cleanup in Emacs, of course, but dos2unix is easier. Go to your Linux computer and run dos2unix on all affected files, then commit any changes that result. If that is the case, I recommend making the file (or files) consistent before continuing. Since the default Emacs behavior is to mimic the line endings already in the file, it may be the case that the file already had mixed line–ending characters and Emacs’ guessing is making the problem worse. There are a number of ways to configure Emacs, so I recommend reading chapter 22.6 Recognizing Coding Systems in the Emacs manual (also available inside Emacs type C-h i to open the Info viewer). So if you commit a file with LF as the line–ending character and then check it out on Windows, Git will write the file to disk with CRLF characters in their place. Git’s default behavior is to convert all line endings in text files to the default line–ending character for the current platform. The other alternative is to leave the Git configuration alone, and reconfigure Emacs. gitattributes file for more information about how to do this. You may have configured Emacs to prefer one line ending over the other, in which case changing the git config to match that preference would simplify the problem. For example, you could configure it to always use LF or always use CRLF, whichever you prefer. ![]() The first is to configure git to always checkout files using a consistent choice of line–ending character on all platforms. There are two avenues you should explore. The diff format doesn’t even include the original line endings from the file all the line endings are replaced with whatever Git thinks is correct for your platform. You might be able to change how the diffs are presented (for example by turning on whitespace mode and configuring it to use visibly distinct glyphs for spaces and tabs, but there’s little that you can do about the line–ending problem. It looks like the diff you are seeing is happening because the line endings have changed, or possibly the other whitespace in the line has changed (tabs to spaces, for example). Instead Git creates the diffs and Magit only presents them. Frankly, I don't care beyond understanding, "how can I silence the noise so that I can see the meaningful differences and just make the commit?" It's probably silly to ask how to "ignore encodings", but I'm not an expert in how encodings function. However, that looks to only work for checkouts I don't think it does anything for the immediate problem of "I want to commit some changes right now". gitattributes might resolve future problems. I understand the problem to be with how each Git repo/clone is configured per system. I conclude that this is the source of the noise. The encoding of init.el on my Windows machine is UTF-8- dos whereas on my GNU machine is UTF-8- unix. My init forces UTF-8: (prefer-coding-system 'utf-8) Configuring magit to ignore line endings, tabs, whitespace, and indentation doesn't silence the noise, so I conclude those aren't the culprit. My magit diff is full of "differences" where there is no visually discernible change.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |